Avenview SW-HDM3D-C5-4X4 User Manual

Browse online or download User Manual for Computer Accessories Avenview SW-HDM3D-C5-4X4. Avenview SW-HDM3D-C5-4X4 User Manual

  • Download
  • Add to my manuals
  • Print
  • Page
    / 19
  • Table of contents
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 0
www.avenview.com
1
4X4 HDMI Matrix Switch with 3D
over CAT-5 with IR Pass-Through
Model #: SW-HDM3D-C5-4X4
© 2011 Avenview Inc. All rights reserved.
The contents of this document are provided in connection with Avenview Inc. (“Avenview”) products. Avenview makes no representations or warranties with
respect to the accuracy or completeness of the contents of this publication and reserves the right to make changes to specifications and product descriptions at any
time without notice. No license, whether express, implied, or otherwise, to any intellectual property rights is granted by this publication. Except as set forth in
Avenview Standard Terms and Conditions of Sale, Avenview assumes no liability whatsoever, and disclaims any express or implied warranty, relating to its products
Page view 0
1 2 3 4 5 6 ... 18 19

Summary of Contents

Page 1

www.avenview.com 1 4X4 HDMI Matrix Switch with 3D over CAT-5 with IR Pass-Through Model #: SW-HDM3D-C5-4X4 © 2011 Avenview In

Page 2 - Table of Contents

www.avenview.com 10 1.7.6 Dip Switch for EDID & Audio Settings (SW1 – SW4) DIP Switch Position Video Audio Description PIN # 1 PIN # 2 OFF  OFF

Page 3 - Section 1: Getting Started

www.avenview.com 11 1.7.7 SW Main Dip Switch for Firmware Update DIP Switch Position PIN # 1 PIN # 2 PIN # 3 PIN # 4 Normal Operation Mode6 OFF  OF

Page 4 - 1.4 Introduction

www.avenview.com 12 1.8 Installation (SW-HDM3D-C5-4X4) To setup Avenview SW-HDM3D-C5-4X4 follow these steps for connecting to a device: 1. Connec

Page 5

www.avenview.com 13 1.9 Operation and IR Control 1.9.1 Source Side 1.9.2 Method A: Push-in Button 1. Push the buttons in the selected range of re

Page 6 - 1.6 Before Installation

www.avenview.com 14 1.10 RS232 Serial Port Control Scan: Press Scan button, the machine will scan the all com port and show them. Select the RS2

Page 7 - 1.7 Panel Description

www.avenview.com 15 Linkage: Press Linkage button to read back all status Open / Close: Press this button to Close or Open COM Port. Mapping Button:

Page 8

www.avenview.com 16 Group setting First select output ports one by one. Then select the input source. The selected output ports change the setting at

Page 9

www.avenview.com 17 Section 2: Specifications Item Description Units SW-HDM3D-C5-4X4 HDM3D-C5SW-R Unit Description 4X4 HDMI Matrix Switch with 3D ove

Page 10

www.avenview.com 18 Notice 1. If the DVI or HDMI device requires the EDID information, please use EDID Reader/Writer to retrieve and provide DV

Page 11

www.avenview.com Disclaimer While every precaution has been taken in the preparation of this document, Avenview Inc. assumes no liability w

Page 12 - Receiver

www.avenview.com 2 including, but not limited to, the implied warranty of merchantability, fitness for a particular purpose, or infringement of any i

Page 13

www.avenview.com 3 Section 1: Getting Started 1.1 Important Safeguards Please read all of these instructions carefully before you use the device. Sa

Page 14

www.avenview.com 4 1.3 Regulatory Notices Federal Communications Commission (FCC) This equipment has been tested and found to comply with Part 15 o

Page 15

www.avenview.com 5

Page 16

www.avenview.com 6 - Silicon Image chipset embedded for best quality, compatibility and reliability - Support HDMI Deep Color & full 3D - HDCP

Page 17 - Section 2: Specifications

www.avenview.com 7 1.7 Panel Description 1.7.1 SW-HDM3D-C5-4X4 Front Panel 1. Port 1-4 SELECT: Push-in button for selecting input channel 2. Por

Page 18

www.avenview.com 8 1.7.3 HDM3D-C5SW-R 1. IR INPUT: Plug in IR receiver. 2. +5V DC: Spare power jack for over 60m transmission when the RX may n

Page 19

www.avenview.com 9 1.7.5 HDM3D-C5SW-R IR Blaster Cable IR Receiver Cable IR Main The default location for IR emitter extension cable to

Comments to this Manuals

No comments