www.avenview.com|1 8x8 HDMI Matrix Switch over Single CAT5/6 With Deep Color & 3D Support © 2012
www.avenview.com|10 1.10 Operation and IR Control 1.10.1 Method A: Push Button 1. IN/OUT MAP 1) Use the “+”or “-“ output push button to select the
www.avenview.com|11 4. Default EDID Mode 1) Push “input+ (default)”button to select the input channel which you want to learn default EDID and then
www.avenview.com|12 1.11 RS232 Serial Port Control 1 FW/SW Version Button 7 Firmware Update Button 2 COM Port Selection 8 Network Button 3 Connec
www.avenview.com|13 2. COM Port Selection Click “ ” button to select COM Port 3. Connection Status 1) Connected Status: 2) Connecting Status
www.avenview.com|14 5. Power On/Off Button Click this button to power on/off “ ” Power on status(Blue): Click this button to power off device(Sta
www.avenview.com|15 1) Learn EDID from Default a) Select Default EDID(1-8 Default EDID) b) Select Input c) Click “Learn” button to learn default
www.avenview.com|16 b) Select the EDID content c) Click “Save EDID on Computer” to save the generated EDID as a file View EDID Content a) Select
www.avenview.com|17 c) Click “Save As” to save the read EDID as a file on computer 7) Firmware Update Button 1) Click “Load File” to select the
www.avenview.com|18 8) Network Button 1) Click “Read From Device” to read the device IP address 2) Select “Ethernet” and then will be a pop-up wi
www.avenview.com|19 2) Preset Mapping: a) Select Mapping(1-8) b) Click “Recall” button to recall previous mapping which are saved 3) Rename M
www.avenview.com|2 Table of Contents Section 1: Getting Started ...
www.avenview.com|20 12) Mute Output Button Click the circle button to turn off output’s video and audio Ex: Mute Output 2
www.avenview.com|21 1.11 EDID Learning Software Control: Please refer to the Operation Approach\ Method C: Software Control through RS-232 port The
www.avenview.com|22 Section 2: Specifications Item Description Units SW-HDM3D-C6-8x8E HDM3D-C6SW-R Unit Description 8x8 HDMI Matrix Switch over CAT6
www.avenview.com|23 Section 3: IR Remote User Guide ON Power on the matrix switcher OFF Standby mode MUTE Hide or Turn off the selected Output
www.avenview.com|24 Operation Procedure 7-Segment LED Mute Output Mute + (Output 1~8) + Take Ex: Mute Output 3 1. Press “MUTE” button - 0 2. Press n
www.avenview.com|25 Learn EDID Port EDID Learn + D(EDID Port) +1~8(Input 1~8) + Take Ex: Learn EDID Port Input 3 1.Press “LEARN” button E L 2.Press
www.avenview.com|3 Section 1: Getting Started 1.1 Important Safeguards Please read all of these instructions carefully before you use the device. Sa
www.avenview.com|4 1.3 Regulatory Notices Federal Communications Commission (FCC) This equipment has been tested and found to comply with Part 15 o
www.avenview.com|5 1.5 Package Contents Before you start the installation of the MARTIX SWITCHER please check the package contents. - SW-HDM3D-C5-
www.avenview.com|6 1.7 Panel Description 1.7.1 SW-HDM3D-C6-8x8E Front Panel 1. SOURCE STATUS: Input source indicator LED 2. IR SENSOR: IR se
www.avenview.com|7 1.7.3 HDM3D-C6SW-R 1. SIGNAL LEVEL: Adjust the 8-level equalization 2. HDMI OUTPUT: Connect to HDTV with a HDMI cable 3. I
www.avenview.com|8 1.8 IR Control Patch IR Blaster Cable IR Receiver Cable IR Sockets SW-HDM3D-C6-8x8E All IR Out: The default location for
www.avenview.com|9 1.9 Installation (SW-HDM3D-C6-8x8E) To setup Avenview SW-HDM3D-C6-8x8E follow these steps for connecting to a device: Matrix Sw
Comments to this Manuals